525 lines
27 KiB
OpenEdge ABL
525 lines
27 KiB
OpenEdge ABL
|
ConfigVersion 2.0
|
||
|
|
;SectionFlags for :
|
||
|
|
; Robot parameter file
|
||
|
|
|
||
|
|
Section General settings
|
||
|
|
;SectionFlags for General settings:
|
||
|
|
Class Pioneer ; general type of robot
|
||
|
|
Subclass patrolbot-sh ; specific type of robot
|
||
|
|
RobotRadius 250.00000 ; radius in mm
|
||
|
|
RobotDiagonal 120.00000 ; half-height to diagonal of octagon
|
||
|
|
RobotWidth 425.00000 ; width in mm
|
||
|
|
RobotLength 510.00000 ; length in mm of the whole robot
|
||
|
|
RobotLengthFront 255.00000 ; length in mm to the front of the robot (if this is
|
||
|
|
; 0 (or non existent) this value will be set to half
|
||
|
|
; of RobotLength)
|
||
|
|
RobotLengthRear 255.00000 ; length in mm to the rear of the robot (if this is 0
|
||
|
|
; (or non existent) this value will be set to half of
|
||
|
|
; RobotLength)
|
||
|
|
Holonomic true ; turns in own radius
|
||
|
|
MaxRVelocity 500 ; absolute maximum degrees / sec
|
||
|
|
MaxVelocity 2200 ; absolute maximum mm / sec
|
||
|
|
MaxLatVelocity 0 ; absolute lateral maximum mm / sec
|
||
|
|
HasMoveCommand true ; has built in move command
|
||
|
|
RequestIOPackets true ; automatically request IO packets
|
||
|
|
RequestEncoderPackets false ; automatically request encoder packets
|
||
|
|
SwitchToBaudRate 38400 ; switch to this baud if non-0 and supported on robot
|
||
|
|
|
||
|
|
Section Conversion factors
|
||
|
|
;SectionFlags for Conversion factors:
|
||
|
|
AngleConvFactor 0.00153 ; radians per angular unit (2PI/4096)
|
||
|
|
DistConvFactor 1.00000 ; multiplier to mm from robot units
|
||
|
|
VelConvFactor 1.00000 ; multiplier to mm/sec from robot units
|
||
|
|
RangeConvFactor 1.00000 ; multiplier to mm from sonar units
|
||
|
|
DiffConvFactor 0.00560 ; ratio of angular velocity to wheel velocity (unused
|
||
|
|
; in newer firmware that calculates and returns this)
|
||
|
|
Vel2Divisor 20.00000 ; divisor for VEL2 commands
|
||
|
|
GyroScaler 1.62600 ; Scaling factor for gyro readings
|
||
|
|
|
||
|
|
Section Accessories the robot has
|
||
|
|
;SectionFlags for Accessories the robot has:
|
||
|
|
TableSensingIR false ; if robot has upwards facing table sensing IR
|
||
|
|
NewTableSensingIR false ; if table sensing IR are sent in IO packet
|
||
|
|
FrontBumpers true ; if robot has a front bump ring
|
||
|
|
NumFrontBumpers 6 ; number of front bumpers on the robot
|
||
|
|
RearBumpers true ; if the robot has a rear bump ring
|
||
|
|
NumRearBumpers 6 ; number of rear bumpers on the robot
|
||
|
|
|
||
|
|
Section IR parameters
|
||
|
|
;SectionFlags for IR parameters:
|
||
|
|
IRNum 0 ; number of IRs on the robot
|
||
|
|
; IRUnit <IR Number> <IR Type> <Persistance, cycles> <x position, mm> <y
|
||
|
|
position, mm>
|
||
|
|
|
||
|
|
Section Movement control parameters
|
||
|
|
; if these are 0 the parameters from robot flash will be used, otherwise these
|
||
|
|
; values will be used
|
||
|
|
;SectionFlags for Movement control parameters:
|
||
|
|
SettableVelMaxes true ; if TransVelMax and RotVelMax can be set
|
||
|
|
TransVelMax 0 ; maximum desired translational velocity for the robot
|
||
|
|
RotVelMax 0 ; maximum desired rotational velocity for the robot
|
||
|
|
SettableAccsDecs true ; if the accel and decel parameters can be set
|
||
|
|
TransAccel 0 ; translational acceleration
|
||
|
|
TransDecel 0 ; translational deceleration
|
||
|
|
RotAccel 0 ; rotational acceleration
|
||
|
|
RotDecel 0 ; rotational deceleration
|
||
|
|
HasLatVel false ; if the robot has lateral velocity
|
||
|
|
LatVelMax 0 ; maximum desired lateral velocity for the robot
|
||
|
|
LatAccel 0 ; lateral acceleration
|
||
|
|
LatDecel 0 ; lateral deceleration
|
||
|
|
|
||
|
|
Section GPS parameters
|
||
|
|
;SectionFlags for GPS parameters:
|
||
|
|
GPSPX 0 ; x location of gps receiver antenna on robot, mm
|
||
|
|
GPSPY 0 ; y location of gps receiver antenna on robot, mm
|
||
|
|
GPSType standard ; type of gps receiver (trimble, novatel, standard)
|
||
|
|
GPSPort COM2 ; port the gps is on
|
||
|
|
GPSBaud 9600 ; gps baud rate (9600, 19200, 38400, etc.)
|
||
|
|
|
||
|
|
Section Compass parameters
|
||
|
|
;SectionFlags for Compass parameters:
|
||
|
|
CompassType robot ; type of compass: robot (typical configuration), or
|
||
|
|
; serialTCM (computer serial port)
|
||
|
|
CompassPort ; serial port name, if CompassType is serialTCM
|
||
|
|
|
||
|
|
Section Sonar parameters
|
||
|
|
;SectionFlags for Sonar parameters:
|
||
|
|
SonarNum 16 ; Number of sonars on the robot.
|
||
|
|
; SonarUnit <sonarNumber> <x position, mm> <y position, mm> <heading of disc,
|
||
|
|
degrees> (for MTX sonar there is also <sonar board> <sonar board unit
|
||
|
|
position> <gain> <detection threshold> <num echo samples>)
|
||
|
|
SonarUnit 0 83 229 90 0 0 0 0 0 0
|
||
|
|
SonarUnit 1 169 202 55 0 0 0 0 0 0
|
||
|
|
SonarUnit 2 232 134 30 0 0 0 0 0 0
|
||
|
|
SonarUnit 3 263 46 10 0 0 0 0 0 0
|
||
|
|
SonarUnit 4 263 -46 -10 0 0 0 0 0 0
|
||
|
|
SonarUnit 5 232 -134 -30 0 0 0 0 0 0
|
||
|
|
SonarUnit 6 169 -202 -55 0 0 0 0 0 0
|
||
|
|
SonarUnit 7 83 -229 -90 0 0 0 0 0 0
|
||
|
|
SonarUnit 8 -83 -229 -90 0 0 0 0 0 0
|
||
|
|
SonarUnit 9 -169 -202 -125 0 0 0 0 0 0
|
||
|
|
SonarUnit 10 -232 -134 -150 0 0 0 0 0 0
|
||
|
|
SonarUnit 11 -263 -46 -170 0 0 0 0 0 0
|
||
|
|
SonarUnit 12 -263 46 170 0 0 0 0 0 0
|
||
|
|
SonarUnit 13 -232 134 150 0 0 0 0 0 0
|
||
|
|
SonarUnit 14 -169 202 125 0 0 0 0 0 0
|
||
|
|
SonarUnit 15 -83 229 90 0 0 0 0 0 0
|
||
|
|
|
||
|
|
Section SonarBoard_1
|
||
|
|
; Information about the connection to this Sonar Board.
|
||
|
|
;SectionFlags for SonarBoard_1:
|
||
|
|
SonarAutoConnect false ; SonarBoard_1 exists and should be automatically
|
||
|
|
; connected at startup.
|
||
|
|
SonarBoardType ; Type of the sonar board.
|
||
|
|
SonarBoardPortType ; Port type that the sonar is on.
|
||
|
|
SonarBoardPort ; Port the sonar is on.
|
||
|
|
SonarBoardPowerOutput ; Power output that controls this Sonar Board's power.
|
||
|
|
SonarBaud 0 ; Baud rate for the sonar board communication. (9600,
|
||
|
|
; 19200, 38400, etc.).
|
||
|
|
SonarDelay 2 ; range [0, 10], Sonar delay (in ms).
|
||
|
|
SonarGain 10 ; range [0, 31], Default sonar gain for the board,
|
||
|
|
; range 0-31.
|
||
|
|
SonarDetectionThreshold 25 ; range [0, 65535], Default sonar detection
|
||
|
|
; threshold for the board.
|
||
|
|
SonarMaxRange 4335 ; range [0, 4335], Default maximum sonar range for
|
||
|
|
; the board.
|
||
|
|
|
||
|
|
Section Laser parameters
|
||
|
|
; Information about the connection to this laser and its position on the
|
||
|
|
; vehicle.
|
||
|
|
;SectionFlags for Laser parameters:
|
||
|
|
LaserAutoConnect false ; Laser_1 exists and should be automatically connected
|
||
|
|
; at startup.
|
||
|
|
LaserX 37 ; Location (in mm) of the laser in X (+ front, - back)
|
||
|
|
; relative to the robot's idealized center of
|
||
|
|
; rotation.
|
||
|
|
LaserY 0 ; Location (in mm) of the laser in Y (+ left, - right)
|
||
|
|
; relative to the robot's idealized center of
|
||
|
|
; rotation.
|
||
|
|
LaserTh 0.00000 ; range [-180, 180], Rotation (in deg) of the laser
|
||
|
|
; (+ counterclockwise, - clockwise).
|
||
|
|
LaserZ 0 ; minimum 0, Height (in mm) of the laser from the
|
||
|
|
; ground. 0 means unknown.
|
||
|
|
LaserIgnore -76--72 72-76 ; Angles (in deg) at which to ignore readings, +/1
|
||
|
|
; one degree. Angles are entered as strings, separated
|
||
|
|
; by a space.
|
||
|
|
LaserFlipped true ; Laser_1 is upside-down.
|
||
|
|
LaserType lms2xx ; Type of laser.
|
||
|
|
LaserPortType serial ; Type of port the laser is on.
|
||
|
|
LaserPort COM3 ; Port the laser is on.
|
||
|
|
LaserPowerOutput ; Power output that controls this laser's power.
|
||
|
|
LaserStartingBaudChoice ; StartingBaud for this laser. Leave blank to use the
|
||
|
|
; default.
|
||
|
|
LaserAutoBaudChoice ; AutoBaud for this laser. Leave blank to use the
|
||
|
|
; default.
|
||
|
|
LaserPowerControlled false ; When enabled (true), this indicates that the power
|
||
|
|
; to the laser is controlled by the serial port line.
|
||
|
|
LaserMaxRange 0 ; Maximum range (in mm) to use for the laser. This
|
||
|
|
; should be specified only when the range needs to be
|
||
|
|
; shortened. 0 to use the default range.
|
||
|
|
LaserCumulativeBufferSize 0 ; Cumulative buffer size to use for the laser. 0 to
|
||
|
|
; use the default.
|
||
|
|
LaserStartDegrees ; Start angle (in deg) for the laser. This may be used
|
||
|
|
; to constrain the angle. Fractional degrees are
|
||
|
|
; permitted. Leave blank to use the default.
|
||
|
|
LaserEndDegrees ; End angle (in deg) for the laser. This may be used
|
||
|
|
; to constrain the angle. Fractional degreees are
|
||
|
|
; permitted. Leave blank to use the default.
|
||
|
|
LaserDegreesChoice ; Degrees choice for the laser. This may be used to
|
||
|
|
; constrain the range. Leave blank to use the default.
|
||
|
|
LaserIncrement ; Increment (in deg) for the laser. Fractional degrees
|
||
|
|
; are permitted. Leave blank to use the default.
|
||
|
|
LaserIncrementChoice ; Increment choice for the laser. This may be used to
|
||
|
|
; increase the increment. Leave blank to use the
|
||
|
|
; default.
|
||
|
|
LaserUnitsChoice ; Units for the laser. This may be used to increase
|
||
|
|
; the size of the units. Leave blank to use the
|
||
|
|
; default.
|
||
|
|
LaserReflectorBitsChoice ; ReflectorBits for the laser. Leave blank to use the
|
||
|
|
; default.
|
||
|
|
|
||
|
|
Section Laser 2 parameters
|
||
|
|
; Information about the connection to this laser and its position on the
|
||
|
|
; vehicle.
|
||
|
|
;SectionFlags for Laser 2 parameters:
|
||
|
|
LaserAutoConnect false ; Laser_2 exists and should be automatically connected
|
||
|
|
; at startup.
|
||
|
|
LaserX 200 ; Location (in mm) of the laser in X (+ front, - back)
|
||
|
|
; relative to the robot's idealized center of
|
||
|
|
; rotation.
|
||
|
|
LaserY 0 ; Location (in mm) of the laser in Y (+ left, - right)
|
||
|
|
; relative to the robot's idealized center of
|
||
|
|
; rotation.
|
||
|
|
LaserTh 0.00000 ; range [-180, 180], Rotation (in deg) of the laser
|
||
|
|
; (+ counterclockwise, - clockwise).
|
||
|
|
LaserZ 0 ; minimum 0, Height (in mm) of the laser from the
|
||
|
|
; ground. 0 means unknown.
|
||
|
|
LaserIgnore ; Angles (in deg) at which to ignore readings, +/1 one
|
||
|
|
; degree. Angles are entered as strings, separated by
|
||
|
|
; a space.
|
||
|
|
LaserFlipped true ; Laser_2 is upside-down.
|
||
|
|
LaserType urg ; Type of laser.
|
||
|
|
LaserPortType serial ; Type of port the laser is on.
|
||
|
|
LaserPort COM5 ; Port the laser is on.
|
||
|
|
LaserPowerOutput ; Power output that controls this laser's power.
|
||
|
|
LaserStartingBaudChoice ; StartingBaud for this laser. Leave blank to use the
|
||
|
|
; default.
|
||
|
|
LaserAutoBaudChoice ; AutoBaud for this laser. Leave blank to use the
|
||
|
|
; default.
|
||
|
|
LaserPowerControlled true ; When enabled (true), this indicates that the power
|
||
|
|
; to the laser is controlled by the serial port line.
|
||
|
|
LaserMaxRange 0 ; Maximum range (in mm) to use for the laser. This
|
||
|
|
; should be specified only when the range needs to be
|
||
|
|
; shortened. 0 to use the default range.
|
||
|
|
LaserCumulativeBufferSize 0 ; Cumulative buffer size to use for the laser. 0 to
|
||
|
|
; use the default.
|
||
|
|
LaserStartDegrees -55 ; Start angle (in deg) for the laser. This may be used
|
||
|
|
; to constrain the angle. Fractional degrees are
|
||
|
|
; permitted. Leave blank to use the default.
|
||
|
|
LaserEndDegrees 55 ; End angle (in deg) for the laser. This may be used
|
||
|
|
; to constrain the angle. Fractional degreees are
|
||
|
|
; permitted. Leave blank to use the default.
|
||
|
|
LaserDegreesChoice ; Degrees choice for the laser. This may be used to
|
||
|
|
; constrain the range. Leave blank to use the default.
|
||
|
|
LaserIncrement 1.0 ; Increment (in deg) for the laser. Fractional degrees
|
||
|
|
; are permitted. Leave blank to use the default.
|
||
|
|
LaserIncrementChoice ; Increment choice for the laser. This may be used to
|
||
|
|
; increase the increment. Leave blank to use the
|
||
|
|
; default.
|
||
|
|
LaserUnitsChoice ; Units for the laser. This may be used to increase
|
||
|
|
; the size of the units. Leave blank to use the
|
||
|
|
; default.
|
||
|
|
LaserReflectorBitsChoice ; ReflectorBits for the laser. Leave blank to use the
|
||
|
|
; default.
|
||
|
|
|
||
|
|
Section Battery_1
|
||
|
|
; Information about the connection to this battery.
|
||
|
|
;SectionFlags for Battery_1:
|
||
|
|
BatteryAutoConnect false ; Battery_1 exists and should be automatically
|
||
|
|
; connected at startup.
|
||
|
|
BatteryType ; Type of battery.
|
||
|
|
BatteryPortType ; Port type that the battery is on.
|
||
|
|
BatteryPort ; Port the battery is on.
|
||
|
|
BatteryBaud 0 ; Baud rate to use for battery communication (9600,
|
||
|
|
; 19200, 38400, etc.).
|
||
|
|
|
||
|
|
Section LCD_1
|
||
|
|
; The physical definition of this LCD.
|
||
|
|
;SectionFlags for LCD_1:
|
||
|
|
LCDAutoConnect false ; LCD_1 exists and should automatically be connected
|
||
|
|
; at startup.
|
||
|
|
LCDDisconnectOnConnectFailure false ; The LCD is a key component and is
|
||
|
|
; required for operation. If this is enabled and there
|
||
|
|
; is a failure in the LCD communications, then the
|
||
|
|
; robot will restart.
|
||
|
|
LCDType ; Type of LCD.
|
||
|
|
LCDPortType ; Port type that the LCD is on.
|
||
|
|
LCDPort ; Port that the LCD is on.
|
||
|
|
LCDPowerOutput ; Power output that controls this LCD's power.
|
||
|
|
LCDBaud 0 ; Baud rate for the LCD communication (9600, 19200,
|
||
|
|
; 38400, etc.).
|
||
|
|
|
||
|
|
Section PTZ 1 parameters
|
||
|
|
; Information about the connection to a pan/tilt unit (PTU) or pan/tilt/zoom
|
||
|
|
; control (PTZ) of a camera
|
||
|
|
;SectionFlags for PTZ 1 parameters:
|
||
|
|
PTZAutoConnect true ; If true, connect to this PTZ by default.
|
||
|
|
PTZType vcc4 ; PTZ or PTU type
|
||
|
|
PTZInverted false ; If unit is mounted inverted (upside-down)
|
||
|
|
PTZSerialPort none ; serial port, or none if not using serial port
|
||
|
|
; communication
|
||
|
|
PTZRobotAuxSerialPort -1 ; Pioneer aux. serial port, or -1 if not using aux.
|
||
|
|
; serial port for communication.
|
||
|
|
PTZAddress 192.168.0.90 ; IP address or hostname, or none if not using network
|
||
|
|
; communication.
|
||
|
|
PTZTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section PTZ 2 parameters
|
||
|
|
; Information about the connection to a pan/tilt unit (PTU) or pan/tilt/zoom
|
||
|
|
; control (PTZ) of a camera
|
||
|
|
;SectionFlags for PTZ 2 parameters:
|
||
|
|
PTZAutoConnect false ; If true, connect to this PTZ by default.
|
||
|
|
PTZType unknown ; PTZ or PTU type
|
||
|
|
PTZInverted false ; If unit is mounted inverted (upside-down)
|
||
|
|
PTZSerialPort none ; serial port, or none if not using serial port
|
||
|
|
; communication
|
||
|
|
PTZRobotAuxSerialPort -1 ; Pioneer aux. serial port, or -1 if not using aux.
|
||
|
|
; serial port for communication.
|
||
|
|
PTZAddress 192.168.0.90 ; IP address or hostname, or none if not using network
|
||
|
|
; communication.
|
||
|
|
PTZTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section PTZ 3 parameters
|
||
|
|
; Information about the connection to a pan/tilt unit (PTU) or pan/tilt/zoom
|
||
|
|
; control (PTZ) of a camera
|
||
|
|
;SectionFlags for PTZ 3 parameters:
|
||
|
|
PTZAutoConnect false ; If true, connect to this PTZ by default.
|
||
|
|
PTZType unknown ; PTZ or PTU type
|
||
|
|
PTZInverted false ; If unit is mounted inverted (upside-down)
|
||
|
|
PTZSerialPort none ; serial port, or none if not using serial port
|
||
|
|
; communication
|
||
|
|
PTZRobotAuxSerialPort -1 ; Pioneer aux. serial port, or -1 if not using aux.
|
||
|
|
; serial port for communication.
|
||
|
|
PTZAddress 192.168.0.90 ; IP address or hostname, or none if not using network
|
||
|
|
; communication.
|
||
|
|
PTZTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section PTZ 4 parameters
|
||
|
|
; Information about the connection to a pan/tilt unit (PTU) or pan/tilt/zoom
|
||
|
|
; control (PTZ) of a camera
|
||
|
|
;SectionFlags for PTZ 4 parameters:
|
||
|
|
PTZAutoConnect false ; If true, connect to this PTZ by default.
|
||
|
|
PTZType unknown ; PTZ or PTU type
|
||
|
|
PTZInverted false ; If unit is mounted inverted (upside-down)
|
||
|
|
PTZSerialPort none ; serial port, or none if not using serial port
|
||
|
|
; communication
|
||
|
|
PTZRobotAuxSerialPort -1 ; Pioneer aux. serial port, or -1 if not using aux.
|
||
|
|
; serial port for communication.
|
||
|
|
PTZAddress 192.168.0.90 ; IP address or hostname, or none if not using network
|
||
|
|
; communication.
|
||
|
|
PTZTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section PTZ 5 parameters
|
||
|
|
; Information about the connection to a pan/tilt unit (PTU) or pan/tilt/zoom
|
||
|
|
; control (PTZ) of a camera
|
||
|
|
;SectionFlags for PTZ 5 parameters:
|
||
|
|
PTZAutoConnect false ; If true, connect to this PTZ by default.
|
||
|
|
PTZType unknown ; PTZ or PTU type
|
||
|
|
PTZInverted false ; If unit is mounted inverted (upside-down)
|
||
|
|
PTZSerialPort none ; serial port, or none if not using serial port
|
||
|
|
; communication
|
||
|
|
PTZRobotAuxSerialPort -1 ; Pioneer aux. serial port, or -1 if not using aux.
|
||
|
|
; serial port for communication.
|
||
|
|
PTZAddress 192.168.0.90 ; IP address or hostname, or none if not using network
|
||
|
|
; communication.
|
||
|
|
PTZTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section PTZ 6 parameters
|
||
|
|
; Information about the connection to a pan/tilt unit (PTU) or pan/tilt/zoom
|
||
|
|
; control (PTZ) of a camera
|
||
|
|
;SectionFlags for PTZ 6 parameters:
|
||
|
|
PTZAutoConnect false ; If true, connect to this PTZ by default.
|
||
|
|
PTZType unknown ; PTZ or PTU type
|
||
|
|
PTZInverted false ; If unit is mounted inverted (upside-down)
|
||
|
|
PTZSerialPort none ; serial port, or none if not using serial port
|
||
|
|
; communication
|
||
|
|
PTZRobotAuxSerialPort -1 ; Pioneer aux. serial port, or -1 if not using aux.
|
||
|
|
; serial port for communication.
|
||
|
|
PTZAddress 192.168.0.90 ; IP address or hostname, or none if not using network
|
||
|
|
; communication.
|
||
|
|
PTZTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section PTZ 7 parameters
|
||
|
|
; Information about the connection to a pan/tilt unit (PTU) or pan/tilt/zoom
|
||
|
|
; control (PTZ) of a camera
|
||
|
|
;SectionFlags for PTZ 7 parameters:
|
||
|
|
PTZAutoConnect false ; If true, connect to this PTZ by default.
|
||
|
|
PTZType unknown ; PTZ or PTU type
|
||
|
|
PTZInverted false ; If unit is mounted inverted (upside-down)
|
||
|
|
PTZSerialPort none ; serial port, or none if not using serial port
|
||
|
|
; communication
|
||
|
|
PTZRobotAuxSerialPort -1 ; Pioneer aux. serial port, or -1 if not using aux.
|
||
|
|
; serial port for communication.
|
||
|
|
PTZAddress 192.168.0.90 ; IP address or hostname, or none if not using network
|
||
|
|
; communication.
|
||
|
|
PTZTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section PTZ 8 parameters
|
||
|
|
; Information about the connection to a pan/tilt unit (PTU) or pan/tilt/zoom
|
||
|
|
; control (PTZ) of a camera
|
||
|
|
;SectionFlags for PTZ 8 parameters:
|
||
|
|
PTZAutoConnect false ; If true, connect to this PTZ by default.
|
||
|
|
PTZType unknown ; PTZ or PTU type
|
||
|
|
PTZInverted false ; If unit is mounted inverted (upside-down)
|
||
|
|
PTZSerialPort none ; serial port, or none if not using serial port
|
||
|
|
; communication
|
||
|
|
PTZRobotAuxSerialPort -1 ; Pioneer aux. serial port, or -1 if not using aux.
|
||
|
|
; serial port for communication.
|
||
|
|
PTZAddress 192.168.0.90 ; IP address or hostname, or none if not using network
|
||
|
|
; communication.
|
||
|
|
PTZTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section Video 1 parameters
|
||
|
|
; Information about the connection to a video acquisition device,
|
||
|
|
; framegrabber, or camera
|
||
|
|
;SectionFlags for Video 1 parameters:
|
||
|
|
VideoAutoConnect true ; If true, connect to this device by default.
|
||
|
|
VideoType v4l ; Device type
|
||
|
|
VideoInverted false ; If image should be flipped (for cameras mounted
|
||
|
|
; inverted/upside-down)
|
||
|
|
VideoWidth -1 ; Desired width of image
|
||
|
|
VideoHeight -1 ; Desired height of image
|
||
|
|
VideoDeviceIndex -1 ; Device index
|
||
|
|
VideoDeviceName none ; Device name (overrides VideoDeviceIndex)
|
||
|
|
VideoChannel 1 ; Input channel
|
||
|
|
VideoAnalogSignalFormat ; NTSC or PAL
|
||
|
|
VideoAddress 192.168.0.90 ; IP address or hostname, or none if not using
|
||
|
|
; network communication.
|
||
|
|
VideoTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section Video 2 parameters
|
||
|
|
; Information about the connection to a video acquisition device,
|
||
|
|
; framegrabber, or camera
|
||
|
|
;SectionFlags for Video 2 parameters:
|
||
|
|
VideoAutoConnect false ; If true, connect to this device by default.
|
||
|
|
VideoType unknown ; Device type
|
||
|
|
VideoInverted false ; If image should be flipped (for cameras mounted
|
||
|
|
; inverted/upside-down)
|
||
|
|
VideoWidth -1 ; Desired width of image
|
||
|
|
VideoHeight -1 ; Desired height of image
|
||
|
|
VideoDeviceIndex -1 ; Device index
|
||
|
|
VideoDeviceName none ; Device name (overrides VideoDeviceIndex)
|
||
|
|
VideoChannel 1 ; Input channel
|
||
|
|
VideoAnalogSignalFormat ; NTSC or PAL
|
||
|
|
VideoAddress 192.168.0.90 ; IP address or hostname, or none if not using
|
||
|
|
; network communication.
|
||
|
|
VideoTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section Video 3 parameters
|
||
|
|
; Information about the connection to a video acquisition device,
|
||
|
|
; framegrabber, or camera
|
||
|
|
;SectionFlags for Video 3 parameters:
|
||
|
|
VideoAutoConnect false ; If true, connect to this device by default.
|
||
|
|
VideoType unknown ; Device type
|
||
|
|
VideoInverted false ; If image should be flipped (for cameras mounted
|
||
|
|
; inverted/upside-down)
|
||
|
|
VideoWidth -1 ; Desired width of image
|
||
|
|
VideoHeight -1 ; Desired height of image
|
||
|
|
VideoDeviceIndex -1 ; Device index
|
||
|
|
VideoDeviceName none ; Device name (overrides VideoDeviceIndex)
|
||
|
|
VideoChannel 1 ; Input channel
|
||
|
|
VideoAnalogSignalFormat ; NTSC or PAL
|
||
|
|
VideoAddress 192.168.0.90 ; IP address or hostname, or none if not using
|
||
|
|
; network communication.
|
||
|
|
VideoTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section Video 4 parameters
|
||
|
|
; Information about the connection to a video acquisition device,
|
||
|
|
; framegrabber, or camera
|
||
|
|
;SectionFlags for Video 4 parameters:
|
||
|
|
VideoAutoConnect false ; If true, connect to this device by default.
|
||
|
|
VideoType unknown ; Device type
|
||
|
|
VideoInverted false ; If image should be flipped (for cameras mounted
|
||
|
|
; inverted/upside-down)
|
||
|
|
VideoWidth -1 ; Desired width of image
|
||
|
|
VideoHeight -1 ; Desired height of image
|
||
|
|
VideoDeviceIndex -1 ; Device index
|
||
|
|
VideoDeviceName none ; Device name (overrides VideoDeviceIndex)
|
||
|
|
VideoChannel 1 ; Input channel
|
||
|
|
VideoAnalogSignalFormat ; NTSC or PAL
|
||
|
|
VideoAddress 192.168.0.90 ; IP address or hostname, or none if not using
|
||
|
|
; network communication.
|
||
|
|
VideoTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section Video 5 parameters
|
||
|
|
; Information about the connection to a video acquisition device,
|
||
|
|
; framegrabber, or camera
|
||
|
|
;SectionFlags for Video 5 parameters:
|
||
|
|
VideoAutoConnect false ; If true, connect to this device by default.
|
||
|
|
VideoType unknown ; Device type
|
||
|
|
VideoInverted false ; If image should be flipped (for cameras mounted
|
||
|
|
; inverted/upside-down)
|
||
|
|
VideoWidth -1 ; Desired width of image
|
||
|
|
VideoHeight -1 ; Desired height of image
|
||
|
|
VideoDeviceIndex -1 ; Device index
|
||
|
|
VideoDeviceName none ; Device name (overrides VideoDeviceIndex)
|
||
|
|
VideoChannel 1 ; Input channel
|
||
|
|
VideoAnalogSignalFormat ; NTSC or PAL
|
||
|
|
VideoAddress 192.168.0.90 ; IP address or hostname, or none if not using
|
||
|
|
; network communication.
|
||
|
|
VideoTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section Video 6 parameters
|
||
|
|
; Information about the connection to a video acquisition device,
|
||
|
|
; framegrabber, or camera
|
||
|
|
;SectionFlags for Video 6 parameters:
|
||
|
|
VideoAutoConnect false ; If true, connect to this device by default.
|
||
|
|
VideoType unknown ; Device type
|
||
|
|
VideoInverted false ; If image should be flipped (for cameras mounted
|
||
|
|
; inverted/upside-down)
|
||
|
|
VideoWidth -1 ; Desired width of image
|
||
|
|
VideoHeight -1 ; Desired height of image
|
||
|
|
VideoDeviceIndex -1 ; Device index
|
||
|
|
VideoDeviceName none ; Device name (overrides VideoDeviceIndex)
|
||
|
|
VideoChannel 1 ; Input channel
|
||
|
|
VideoAnalogSignalFormat ; NTSC or PAL
|
||
|
|
VideoAddress 192.168.0.90 ; IP address or hostname, or none if not using
|
||
|
|
; network communication.
|
||
|
|
VideoTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section Video 7 parameters
|
||
|
|
; Information about the connection to a video acquisition device,
|
||
|
|
; framegrabber, or camera
|
||
|
|
;SectionFlags for Video 7 parameters:
|
||
|
|
VideoAutoConnect false ; If true, connect to this device by default.
|
||
|
|
VideoType unknown ; Device type
|
||
|
|
VideoInverted false ; If image should be flipped (for cameras mounted
|
||
|
|
; inverted/upside-down)
|
||
|
|
VideoWidth -1 ; Desired width of image
|
||
|
|
VideoHeight -1 ; Desired height of image
|
||
|
|
VideoDeviceIndex -1 ; Device index
|
||
|
|
VideoDeviceName none ; Device name (overrides VideoDeviceIndex)
|
||
|
|
VideoChannel 1 ; Input channel
|
||
|
|
VideoAnalogSignalFormat ; NTSC or PAL
|
||
|
|
VideoAddress 192.168.0.90 ; IP address or hostname, or none if not using
|
||
|
|
; network communication.
|
||
|
|
VideoTCPPort 80 ; TCP Port to use for HTTP network connection
|
||
|
|
|
||
|
|
Section Video 8 parameters
|
||
|
|
; Information about the connection to a video acquisition device,
|
||
|
|
; framegrabber, or camera
|
||
|
|
;SectionFlags for Video 8 parameters:
|
||
|
|
VideoAutoConnect false ; If true, connect to this device by default.
|
||
|
|
VideoType unknown ; Device type
|
||
|
|
VideoInverted false ; If image should be flipped (for cameras mounted
|
||
|
|
; inverted/upside-down)
|
||
|
|
VideoWidth -1 ; Desired width of image
|
||
|
|
VideoHeight -1 ; Desired height of image
|
||
|
|
VideoDeviceIndex -1 ; Device index
|
||
|
|
VideoDeviceName none ; Device name (overrides VideoDeviceIndex)
|
||
|
|
VideoChannel 1 ; Input channel
|
||
|
|
VideoAnalogSignalFormat ; NTSC or PAL
|
||
|
|
VideoAddress 192.168.0.90 ; IP address or hostname, or none if not using
|
||
|
|
; network communication.
|
||
|
|
VideoTCPPort 80 ; TCP Port to use for HTTP network connection
|